|
|
Lubricant film formation in compliant contact
Jaroš, Tomáš ; Čermák, Jan (referee) ; Nečas, David (advisor)
This diploma thesis deals with the study of film formation in compliant contact. Primary attention is dedicated to the influence of the entrainment speed and slide-to-roll ratio (SRR) on the central film thickness. Based on a research study of the available experimental methods, the fluorescence microscopy was used to achieve the aim of the work. Experiments were realized in ball-on-disk configuration. Firstly, a validation of the method was performed where the solid contact of the ceramic ball and the glass disk was analyzed. Since the measured values were in a good agreement with the theoretical prediction, a ball of NBR rubber material, which is commonly used for production of lip seals and o-rings, was subsequently used. The experimental measurements were performed under pure rolling and rolling/sliding conditions when the entrainment speeds varied in the range from 10 to 400 mm / s. A constant load of 0.2 N was applied. The measured data were then compared to the theoretical predictions for compliant contacts. The results showed that the thickness of the lubricating film gradually increases with increasing entrainment speed, which corresponds to theoretical assumption. Against expectations, evident influence of SRR on the film formation has been observed. In the last part of the thesis the measured data are confronted with previously published studies. Finally, some limitations of this study are discussed and recommendations for further improvement of the used experimental method are suggested.
|
|
|
The effect of viscoelasticity and operating conditions on friction of compliant contacts
Quinn, Cheney ; Daniel, Matej (referee) ; Nečas, David (advisor)
Poddajné kontakty obsahující polymerní nebo pryžové členy lze nalézt v technických i biologických aplikacích. I přes vývoj v této oblasti existují efekty, které ovlivňují tribologické aspekty těchto kontaktů, a je třeba je dále zkoumat. Tato práce se zabývá vlivy kinematických podmínek, konfigurace, viskoelasticity a viskozity maziva na tření v mazaných poddajných kontaktech. Výsledky byly použity k vývoji numerického modelu pro predikci kapalinového tření v poddajných kontaktech. K objasnění chování poddajných kontaktů bylo použito zařízení Mini Traction Machine (MTM) v konfiguraci ball-on-disc, což umožnilo zkoumání zmíněných vlivů. Z poznatků z technické oblasti bylo zjištěno, že viskoelasticita se projevuje ve všech konfiguracích, tedy soft-on-hard, hard-on-soft a soft-on-soft, a její efekt je nejvýznamnější v konfiguracích s poddajným diskem. Data dále ukazují, že poměr skluzu a valení má vliv na valivé tření což je v rozporu se současnou literaturou. Výsledky z biologické oblasti naznačují, že za určitých podmínek lze nahradit nativní kapalinu jednoduchým mazivem. Tyto poznatky mohou posloužit jako odrazový můstek pro další studie zabývající se poddajnými kontakty.
|
|
|
An experimental investigation of friction coefficient in hip joint replacements
Tkadlec, Tadeáš ; Urban, Filip (referee) ; Nečas, David (advisor)
This bachelor thesis deals with an experimental analysis of friction coefficient within hip joint replacements. The measurements were realized on Mini Traction Machine device in ball-on-disc configuration. The main goal was to determine the effect of implant material, kinematic conditions and model synovial fluid composition on the development of coefficient of friction as a function of time. For this purpose, three different materials (metal, ceramic, polymer), two mean speeds (5.7 mm/s; 22m/s), three different slide-to-roll ratios (SRR = 0 %, SRR = -150 %; SRR = 150 %) and six various model fluids containing albumin and -globulin in a various ratios and concentrations were employed. The results are evaluated in the form of graphs showing the dependence of friction coefficient on time and are confronted with previously published studies.
|
|
|
The effect of viscoelasticity and operating conditions on friction of compliant contacts
Quinn, Cheney ; Daniel, Matej (referee) ; Nečas, David (advisor)
Poddajné kontakty obsahující polymerní nebo pryžové členy lze nalézt v technických i biologických aplikacích. I přes vývoj v této oblasti existují efekty, které ovlivňují tribologické aspekty těchto kontaktů, a je třeba je dále zkoumat. Tato práce se zabývá vlivy kinematických podmínek, konfigurace, viskoelasticity a viskozity maziva na tření v mazaných poddajných kontaktech. Výsledky byly použity k vývoji numerického modelu pro predikci kapalinového tření v poddajných kontaktech. K objasnění chování poddajných kontaktů bylo použito zařízení Mini Traction Machine (MTM) v konfiguraci ball-on-disc, což umožnilo zkoumání zmíněných vlivů. Z poznatků z technické oblasti bylo zjištěno, že viskoelasticita se projevuje ve všech konfiguracích, tedy soft-on-hard, hard-on-soft a soft-on-soft, a její efekt je nejvýznamnější v konfiguracích s poddajným diskem. Data dále ukazují, že poměr skluzu a valení má vliv na valivé tření což je v rozporu se současnou literaturou. Výsledky z biologické oblasti naznačují, že za určitých podmínek lze nahradit nativní kapalinu jednoduchým mazivem. Tyto poznatky mohou posloužit jako odrazový můstek pro další studie zabývající se poddajnými kontakty.
|
|
|
Lubricant film formation in compliant contact
Jaroš, Tomáš ; Čermák, Jan (referee) ; Nečas, David (advisor)
This diploma thesis deals with the study of film formation in compliant contact. Primary attention is dedicated to the influence of the entrainment speed and slide-to-roll ratio (SRR) on the central film thickness. Based on a research study of the available experimental methods, the fluorescence microscopy was used to achieve the aim of the work. Experiments were realized in ball-on-disk configuration. Firstly, a validation of the method was performed where the solid contact of the ceramic ball and the glass disk was analyzed. Since the measured values were in a good agreement with the theoretical prediction, a ball of NBR rubber material, which is commonly used for production of lip seals and o-rings, was subsequently used. The experimental measurements were performed under pure rolling and rolling/sliding conditions when the entrainment speeds varied in the range from 10 to 400 mm / s. A constant load of 0.2 N was applied. The measured data were then compared to the theoretical predictions for compliant contacts. The results showed that the thickness of the lubricating film gradually increases with increasing entrainment speed, which corresponds to theoretical assumption. Against expectations, evident influence of SRR on the film formation has been observed. In the last part of the thesis the measured data are confronted with previously published studies. Finally, some limitations of this study are discussed and recommendations for further improvement of the used experimental method are suggested.
|
|
|
An experimental investigation of friction coefficient in hip joint replacements
Tkadlec, Tadeáš ; Urban, Filip (referee) ; Nečas, David (advisor)
This bachelor thesis deals with an experimental analysis of friction coefficient within hip joint replacements. The measurements were realized on Mini Traction Machine device in ball-on-disc configuration. The main goal was to determine the effect of implant material, kinematic conditions and model synovial fluid composition on the development of coefficient of friction as a function of time. For this purpose, three different materials (metal, ceramic, polymer), two mean speeds (5.7 mm/s; 22m/s), three different slide-to-roll ratios (SRR = 0 %, SRR = -150 %; SRR = 150 %) and six various model fluids containing albumin and -globulin in a various ratios and concentrations were employed. The results are evaluated in the form of graphs showing the dependence of friction coefficient on time and are confronted with previously published studies.
|
guest ::
